Multi-Inlet Vertical Sump Pump

Multi-Inlet Vertical Sump Pump

The multi-inlet sump pump is a vertical suspended sewage pump built around a non-clogging hydraulic design. Depending on the model, it uses a single- or double-channel flow passage and a single- or double-vane impeller. Developed with reference to comparable products, the pump is intended for wastewater containing solid particles and fibers. Its design features include a simple structure, convenient installation, low noise, high efficiency, reduced sediment buildup and energy-saving operation.
Envíeconsulta
Descripción

 

The multi-inlet sump pump is a vertical suspended sewage pump built around a non-clogging hydraulic design. Depending on the model, it uses a single- or double-channel flow passage and a single- or double-vane impeller. Developed with reference to comparable products, the pump is intended for wastewater containing solid particles and fibers. Its design features include a simple structure, convenient installation, low noise, high efficiency, reduced sediment buildup and energy-saving operation.

Representative series include PWDDFL vertical suspended sump pumps, PWDL pumps with upper and lower bearings, PWCL corrosion-resistant pumps, KDZY slurry pumps and PW pumps.

The pump consists primarily of a vertical motor and pump assembly, directly coupled together. Each unit has four suction heads-one main head and three auxiliary heads. The auxiliary heads also serve as pump supports. The pump is described as a double-suction centrifugal solids-handling pump, with an open or semi-open impeller for conveying high-concentration slurry and liquids containing substantial amounts of solids.

The product range covers more than 27 sizes across several series, with performance and installation options to suit different duties.

 

  • Multiple suction heads and anti-sedimentation design
  • L:

 

 

1. Multiple suction heads help limit sediment buildup

Each pump has four suction heads arranged at the center and corners of the pump pit. This distributed arrangement increases the area covered by suction and helps reduce dead zones where sludge can accumulate, particularly in areas farther from a single suction inlet.

Some models add a ring-shaped suction pipe between the heads, with openings arranged at progressively varying intervals to further reduce sediment accumulation on the pit floor.

2. Agitator and cutter improve clog resistance

An agitator beneath the main suction head suspends settled sand, sludge and other solids so they can be pumped away. An umbrella-shaped plate beneath the main head helps prevent air from being drawn into the pump while the agitator is operating.

A metal cutter above the agitator wheel is designed to break up flexible debris such as gloves, cloth and plastic bags, helping reduce wrapping and blockage at the impeller or suction openings.

3. No fixed anchoring required for standard installation

On this design, the auxiliary suction heads also support the pump. For a standard installation, the pump can be placed in the pit and connected to the discharge pipe without being fixed to embedded pit hardware. This simplifies installation, removal and pit cleaning. A support bracket can also be used if required by site conditions.

4. Non-clogging flow passages

The pump uses single- or double-channel passages and single- or double-vane impellers. Its open or semi-open impeller is designed to provide good solids passage and high efficiency.

The source describes a three-blade impeller with curved, single-circular-arc vanes. The impeller also helps agitate the liquid, reducing the need for a separate conventional agitator assembly. Removing supports around the suction heads is intended to improve passage of plastic bags and fibrous debris.

5. Compact submerged installation

The pump is installed with its lower section immersed in the liquid, making the arrangement compact and space-efficient. The source describes the pump as operating smoothly with low vibration and noise and as suitable for convenient operation and automatic control.

Four frame oil seals and a shaft sleeve are fitted in the pump base to protect the shaft from wear and extend its service life. Seal arrangements vary by model; see the technical notes below.

6. Materials can be selected for the duty

Cast iron and cast steel are standard material options. For higher-temperature service, the source lists duplex alloy steel for temperatures up to 180℃. Engineering plastics, including UHMWPE, and stainless steels are available for corrosive service.

7. Vertical or inclined installation

The pump can be installed vertically or at an incline. The volute must remain immersed in the working medium, allowing the pump to start without priming. Overall pump length is available in different configurations to suit the installation.

8. Broad range of media

The source states that the pump can handle instantaneous medium concentrations of up to 30–45%, with solid-particle sizes of 5–30 mm, depending on discharge size. Particle specific gravity is listed as unrestricted. The stated pH range is 1–11 with special materials.

 

 

The multi-inlet sump pump is intended for slurry, sludge, sand slurry, pulp and other liquids containing solids. Listed applications include:

  • Coal-water sumps at thermal power plants and coal-washing facilities, wastewater containing coal residue, ash-pit drainage and flue-gas desulfurization systems.
  • Mine-water drainage, acidic mineral slurry transfer, sand washing and wastewater lifting at mineral-processing plants.
  • Municipal wastewater systems, sludge transfer in urban waterways, stormwater and sewage lifting, primary-settling-tank sludge removal, septic-tank cleaning and stormwater discharge.
  • Basement and excavation-pit drainage, and fire-water pressure boosting.
  • Auxiliary pumping duties and transfer of liquids containing mud and small gravel in coal mines.
  • Contaminated wastewater and thick liquids, dirty liquids, pastes and fluidized sand from chemical, dyeing, pharmaceutical, foundry and food-processing facilities.
  • Pulp discharge and transfer of wastewater containing fibers.
  • Shipboard bilge wastewater and sludge removal.
  • Wastewater stations at hospitals and hotels, biogas-digester slurry, agricultural irrigation, raw-water transfer, aquaculture, civil-defense drainage stations and waterworks drainage.

 

 

1. Design and Construction

The pump is a single- or double-suction vertical centrifugal pump installed as a submerged suspended unit. Main components include the vertical motor, motor base, coupling, bearing housing and bearings, main shaft, cylindrical support, five-way connector, shaft sleeve, pump cover, impeller, casing, main suction head, auxiliary suction heads, agitator shaft and agitator wheel.

The source states that the discharge direction is at 70℃ to the pump-shaft axis; confirm the intended reference direction on the assembly drawing.

2. Drive and Rotation

The motor is directly coupled to the pump. Viewed from the motor fan end, the specified direction of rotation is clockwise.

3. Series and Speeds

The range is described as comprising three configurations, three series and 27 sizes. Standard speeds are 980, 1,450 or 2,900 r/min.

4. Impeller

The impeller has three curved, single-circular-arc blades and is available in semi-open or open construction. The source lists malleable cast iron as an impeller material option, citing its strength, corrosion resistance and ease of machining.

5. Shaft and Sealing

The pump shaft is made from cold-drawn high-quality carbon-steel round bar, reducing shaft weight and machining requirements. Four frame oil seals and a shaft sleeve are fitted in the pump base to protect the shaft from wear.

6. PWDL Upper-and-Lower-Bearing Design

The PWDL model is broadly similar in construction and outline to the PWDDFL, but does not use a bearing box. Instead, its bearings are arranged above and below, in two bearing housings spaced farther apart. The shaft end uses a mechanical seal.

The source states that this arrangement reduces shaft deflection and may extend shaft life. The overall pump height is approximately 330 mm less than that of the PWDDFL model.

7. Operating Conditions

  • 5–3,500 m³/h across the series
  • 5–120 m
  • 980, 1,450 or 2,900 r/min
  • 50 Hz
  • 380 V or 660 V
  • <=40℃ for standard cast-iron or cast-steel models
  • <=60℃ for PWDL
  • Up to 180℃ for special materials such as duplex alloy steel
  • 4–10 for standard materials; 1–11 for special materials
  • 5–15 mm for discharge diameters <=80 mm
  • 15–30 mm for discharge diameters of 100–150 mm
  • Above 30 mm for discharge diameters of 200–300 mm
  • Up to 30–45%
  • Solid-particle specific gravity:
  • Particle diameter up to 30% of the discharge diameter; fiber length up to three times the discharge diameter

 

8. Lifting and Operating Precautions

a. Protect the pump from impact or other damage during lifting.

b. Do not place the pump directly at the wastewater-pit inlet. If the pump base rests on mud or loose sand, vibration may cause it to sink. Use a larger baseplate where needed.

c. The pump may continue operating when the ambient temperature falls below 0℃, provided the wastewater itself has not frozen.

d. The discharge-pipe internal diameter should match the pump outlet diameter. A larger pipe may be used, but do not reduce the pipe diameter below the pump outlet size.

e. Sludge and debris accumulating around a pump in wastewater can reduce conveying performance and shorten service life. Where the pit contains substantial debris, a screen may be fitted around the pump to prevent large objects from entering. Size the screen openings and open area so they do not restrict suction.

f. Do not move or lift the pump until the power supply has been disconnected.

g. The pump may be installed vertically or at an incline. Keep the volute submerged during operation; priming is not required.

h. Follow the applicable general machinery installation procedures.

 

 

6

 

 

 

25PWDDFL-8

4

8

0.75

25

-

-

25PWDDFL-10

6

10

1.1

25

-

-

25PWDDFL-12

8

12

1.5

25

-

-

32PWDDFL-8

8

8

1.1

32

-

-

32PWDDFL-10

10

10

1.5

32

-

-

32PWDDFL-15

12

15

2.2

32

-

-

40PWDDFL-10

15

10

2.2

40

7

-

40PWDDFL-15

18

15

3

40

7

-

40PWDDFL-20

20

20

4

40

7

-

50PWDDFL-12

25

12

3

50

10

-

50PWDDFL-18

30

18

4

50

10

-

50PWDDFL-25

35

25

5.5

50

10

-

65PWDDFL-12

40

12

4

65

12

-

65PWDDFL-18

50

18

5.5

65

12

-

65PWDDFL-25

60

25

7.5

65

12

-

65PWDDFL-32

70

32

11

65

12

-

80PWDDFL-13

60

13

5.5

80

15

-

80PWDDFL-20

80

20

11

80

15

-

80PWDDFL-30

100

30

15

80

15

-

80PWDDFL-38

120

38

22

80

15

-

100PWDDFL-15

100

15

11

100

20

-

100PWDDFL-22

120

22

15

100

20

-

100PWDDFL-32

150

32

22

100

20

-

100PWDDFL-45

180

45

30

100

20

-

125PWDDFL-18

150

18

15

125

25

-

125PWDDFL-28

200

28

30

125

25

-

125PWDDFL-40

250

40

37

125

25

-

125PWDDFL-55

300

55

55

125

25

-

150PWDDFL-18

250

18

22

150

30

-

150PWDDFL-30

350

30

45

150

30

-

150PWDDFL-42

400

42

75

150

30

-

150PWDDFL-60

450

60

90

150

30

-

200PWDDFL-22

400

22

45

200

35

-

200PWDDFL-35

500

35

75

200

35

-

200PWDDFL-50

600

50

110

200

35

-

200PWDDFL-65

650

65

160

200

35

-

250PWDDFL-25

600

25

75

250

40

-

250PWDDFL-42

750

42

132

250

40

-

250PWDDFL-58

800

58

185

250

40

-

300PWDDFL-28

800

28

110

300

50

-

300PWDDFL-45

950

45

185

300

50

-

300PWDDFL-65

1000

65

250

300

50

-

If you cannot find the required specifications or model in our product range, please contact us at any time. Our technical specialists will provide prompt model selection assistance and a customized technical solution.

Etiqueta: Multi-Inlet Vertical Sump Pump, China Multi-Inlet Vertical Sump Pump manufacturers, factory

Envíeconsulta